Востановление загрузки Vu+ unо

  • 2 Ответов
  • 5354 Просмотров
Описание:
*

Оффлайн konditerАвтор темы

  • Проходил мимо
  • *
  • 2
Востановление загрузки Vu+ unо
« Сообщение: Понедельник 20 Январь 2020, 18:07:41 »
Народ всем привет ...
ну подскажите кто сталкивался .. что не так .. не грузиться uno..
чел принёс просит помощи.. восстановить.. Starting.. бесконечный..
говорит rm баловался ну и видать что то снёс жизненно важное..
перезаписать имидж этот вариант не подходит .. нужно выдернуть с начало важную инфу из fs..
Спойлер
CFE initialized.

checking usb
ACK :
writing vfd
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
***************************************************
x = 0, y= 0, bmpMemory=85000000, surfaceMemory=ac800000, splashPitch=1440, splashWidth=720, splashHeight=576
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3`
Loading: 0x80001000/7209248 0x806e1120/127104 Entry address is 0x80567030
TP1 Entry Address at 0x80000ffc = 80567030
Starting program at 0x80567030

Linux version 3.1.1 (build@plibuildserver) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Wed Jan 30 05:00:41 CET 2013
Fetching vars from bootloader... found 11 vars.
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
 memory: 10000000 @ 20000000 (usable)
bmem: adding 232 MB RESERVED region at 24 MB (0x0e800000@0x01800000)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x00010000
    0: 0x00020000 -> 0x00030000
PERCPU: Embedded 7 pages/cpu @81407000 s4384 r8192 d16096 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129536
Kernel command line: bmem=232M ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw rootflags=sync
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 274964k/524288k available (5590k kernel code, 249324k reserved, 1219k data, 232k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Detected MIPS clock frequency: 405 MHz (202.500 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
SMP: CPU1 is running
Brought up 2 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource upg
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
fuse init (API version 7.17)
msgmni has been set to 537
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:04:21:63)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, major 254
IR NEC protocol handler initialized
IR RC5(x) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
Linux video capture interface: v2.00
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
EBI CS0: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0

Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=ecf10095, tim1=4232222d, tim2=00000d94
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=40000101, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=15142200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Creating 8 MTD partitions on "brcmnand.0":
0x000000000000-0x000007200000 : "rootfs"
0x000007200000-0x000007600000 : "kernel"
0x000007600000-0x000007a00000 : "boot"
0x000007a00000-0x000007c00000 : "splash"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: max. sequence number:       589173
UBI: attached mtd0 to ubi0
UBI: MTD device name:            "rootfs"
UBI: MTD device size:            114 MiB
UBI: number of good PEBs:        910
UBI: number of bad PEBs:         2
UBI: number of corrupted PEBs:   0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 910
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2078/648
UBI: image sequence number:  1635167103
UBI: background thread "ubi_bgt0d" started, PID 46
ata1: link is slow to respond, please be patient (ready=-19)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: ST32000542AS, CC94, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      ST32000542AS     CC94 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link down (SStatus 4 SControl 300)
UBIFS: parse sync
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   112500736 bytes (109864 KiB, 107 MiB, 886 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 232k freed
Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
Rebooting in 180 seconds..
[свернуть]

printenv показывает

    CFE> printenv
    Variable Name        Value
    -------------------- --------------------------------------------------
            BOOT_CONSOLE uart0
       LINUX_FFS_STARTAD 0
          LINUX_FFS_SIZE 7200000
      LINUX_PART_STARTAD 7200000
         LINUX_PART_SIZE 400000
     SPLASH_PART_STARTAD 7a00000
        SPLASH_PART_SIZE 200000
                  SPLASH ENABLE
                 STARTUP boot -z -elf flash0.kernel: 'rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3`
             ETH0_HWADDR 00:1D:EC:04:21:63
              DRAM0_SIZE 512
              DRAM1_SIZE 0
              FLASH_TYPE NAND
              FLASH_SIZE 128
             CFE_VERSION 2.12.26
           CFE_BOARDNAME BCM97405B1
          CFE_MEMORYSIZE 128
    *** command status = 0
    CFE>




 


*

Оффлайн admin

  • Администратор
  • *
  • 12.051
  • Понравилось 13.966 раз
  • Пол: Мужской
    • Спутники которые я принимаю 4°W-90°Е
      Мой тюнер Amiko SHD-8900 Alien + WinQuest MR-460 ULTRA
Востановление загрузки Vu+ unо
« Ответ #1: Понедельник 20 Январь 2020, 19:24:10 »
Цитата(konditer от Понедельник  20 Январь 2020, 18:07:41)  Цитата
чел принёс просит помощи.. восстановить.. Starting.. бесконечный..
говорит rm баловался ну и видать что то снёс жизненно важное..
По FTP не даёт подключиться?Чтобы подконнектиться и хотя бы с дистрибутивом сравнить что он там наворотил.Телнет?Хоть что-то работает?Чтобы физически можно было посмотреть что осталось?
Он команду rm не помнит?Хотя это конечно жесть,таким в Линуксе баловаться.




 


*

Оффлайн konditerАвтор темы

  • Проходил мимо
  • *
  • 2
Востановление загрузки Vu+ unо
« Ответ #2: Четверг 23 Январь 2020, 14:18:25 »
Да нет сети ... только порт 232..
help в консоли пишет есть такие вещи..
щас покумекаю..
    CFE> help
    Available commands:

    ts                  Time stamp utility
    erase_flash2        delete 2th mtd
    erase_flash0        delete 0th mtd
    info                Show CFE configuration information
    loop                Loop a command
    reboot              Reboot the system
    dir                 List the directory of a FAT file system
    macprog             Program MAC addresses.
    macprog2            Program a specific MAC address.
    flash               Update a flash memory device
    memtest             Test memory.
    f                   Fill contents of memory.
    e                   Modify contents of memory.
    d                   Dump memory.
    u                   Disassemble instructions.
    batch               Load a batch file into memory and execute it
    go                  Start a previously loaded program.
    load                Load an executable file into memory without executing it
    save                Save a region of memory to a remote file via TFTP
    boot                Load an executable file into memory and execute it
    ping                Ping a remote IP host.
    ifconfig            Configure the Ethernet interface
    sleep               Sleep for specified milliseconds.
    waitusb             Wait for USB device to be installed.
    show usb            Display devices connected to USB bus.
    show heap           Display information about CFE's heap
    show memory         Display the system physical memory map.
    show devices        Display information about the installed devices.
    unsetenv            Delete an environment variable.
    printenv            Display the environment variables
    setenv              Set an environment variable.
    help                Obtain help for CFE commands

    For more information about a command, enter 'help command-name'
    *** command status = 0
    CFE>

    *** command status = 0
    CFE> ifconfig
    Network interface has not been configured
    *** command status = 0
    CFE>
пишет сетевой интерфейс не настроенный типо..




 
« Последнее редактирование: Четверг 23 Январь 2020, 14:43:36 от konditer »



Кто онлайн

Просматривают тему:
0 Пользователей и 1 Гость
 

Похожие темы

Тема / Автор